Max Cat Net

Cat Net Mesh Size and Strand Diameter: How to Specify and Measure Them

When comparing cat net quotations, “30 mm mesh” and “1 mm wire” are not enough to identify the same product. A useful specification separates the mesh opening, the finished strand, any internal reinforcement and the overall panel dimensions. It also states how each dimension is measured.

This guide helps distributors, importers and installers prepare a specification that can be checked against a sample and reused for later orders.

Illustrative views of cat netting for a specification discussion
Illustrative net appearance. These images do not establish mesh dimensions, material composition or an approved installation.

Separate mesh size, strand diameter and panel size

Specification field What it describes What to record
Mesh size The repeated openings in the net, rather than the overall panel. Nominal size, measurement points, mesh orientation and measurement condition.
Nylon monofilament or finished strand diameter The nylon filament itself, or the outside dimension of the complete reinforced strand. Which component is measured, its nominal diameter, the measurement method and agreed tolerance.
Internal wire specification The reinforcement inside a wire-reinforced strand. Wire material and grade, diameter, quantity and construction, confirmed for the quoted product.
Net panel dimensions The overall width and length of a supplied piece. Width × length, orientation, edge treatment and the condition in which dimensions are checked.

Keep the units explicit: mesh and strand dimensions in millimetres, and panel dimensions in metres. A 3 × 4 m panel size does not tell you its mesh size or strand diameter.

Transparent nylon and wire-reinforced net need different descriptions

Transparent nylon cat protection net uses nylon monofilament. The filament diameter is a relevant field to agree alongside mesh size and panel dimensions.

Wire-reinforced cat net has an HDPE net structure with wire reinforcement. Its finished strand diameter and internal wire diameter are separate fields. Ask for both where they are needed to identify the product; a single “1 mm” description does not establish which component was measured.

If a quotation includes a construction code such as “12+1”, request its written definition and a matching sample reference. The code alone should not substitute for the material and construction specification.

Use catalogue options to start an enquiry

The following are product-family options listed in MaxCatNet’s supplied catalogue. They are a starting point for a specification request. The chosen mesh, strand, colour and panel combination needs confirmation in the quotation and sample approval.

Product family Nominal mesh options in the catalogue Diameter information
Transparent nylon monofilament 20 × 20, 25 × 25, 30 × 30 and 50 × 50 mm Catalogue filament options: 0.4, 0.5, 0.6, 0.7, 0.8 and 0.9 mm. Confirm availability for the chosen mesh and panel.
HDPE net with wire reinforcement 20 × 20, 30 × 30 and 50 × 50 mm Request the finished strand and internal wire specifications for the quoted construction.

These lists do not establish every possible combination as a stocked SKU. Before ordering, agree whether the quoted mesh dimension means the clear opening or another measurement basis, and how any tolerance will be assessed.

Agree how mesh size will be measured

A clear-opening measurement uses the inside edges of the surrounding strands. A centre-to-centre measurement uses the centres of those strands. These are different reference points, so the quotation, sample photo and inspection record should name the same basis.

Also record how the mesh is arranged during measurement. A photograph of a relaxed, distorted opening is not directly comparable with a sample held in a different shape or under tension.

  1. Identify the sample. Give it a reference and record the product family, colour, panel size and any construction code.
  2. Mark the measurement points. Show the two points used for each mesh dimension. If tension is applied, ask the supplier to state the agreed condition rather than describing it only as “stretched”.
  3. Take an overview and a close-up. Include a ruler in the same plane as the mesh and keep the measurement points visible. Use the image to explain the method, alongside the written measurement.
  4. Define the diameter check separately. Agree the instrument, contact pressure, measurement location and tolerance with the supplier. An overall net photo cannot establish the diameter of an internal wire.
  5. Agree the sampling plan. Specify where and how many measurements will be taken for approval and later orders. Do not treat one photographed opening as an inspection of an entire batch.

This is a practical specification checklist. The supplier and buyer still need to agree the measurement and acceptance method for the selected product.

Put the approved details into the order record

Use a separate field for each requirement so a supplier can identify an exception before you approve the quote. This blank template can be copied into an enquiry:

  • Application and installation context:
  • Product family and colour:
  • Nominal mesh size, measurement basis and tolerance:
  • Nylon filament or finished strand diameter, method and tolerance:
  • Internal wire specification and construction, if applicable:
  • Panel width × length, dimension orientation and edge treatment:
  • Panel only or kit; agreed accessory list:
  • Quantity, packaging, label language and destination:
  • Sample reference, approval date and agreed inspection method:

Leave unknown fields open for confirmation instead of copying a value from a different construction. For repeat orders, identify the approved reference and list any changes. Our sample panel approval guide for distributors explains how to keep sample and bulk-order records connected.

Frequently asked questions

Does “30 mm mesh” always mean a 30 mm clear opening?

No measurement basis should be assumed from the number alone. Ask whether it refers to the clear opening or another stated method, and confirm the mesh orientation and measurement condition.

Is a “1 mm strand” the same as a “1 mm internal wire”?

No. The finished strand and its internal reinforcement are different components. The quotation should identify what the dimension describes and link it to the selected construction.

Can every listed nylon diameter be ordered with every mesh size?

The catalogue lists family options, rather than a confirmed matrix of all combinations. Send the required combination for availability, sample and quotation confirmation.

Does a smaller mesh size alone establish suitability for a cat?

No. Suitability also depends on the individual cat, the complete boundary, fixing method, installation and ongoing inspection. A nominal mesh dimension is not a universal safety guarantee. Confirm the application and follow the instructions for the chosen product.

What should stay the same on a repeat order?

Reference the approved material, mesh and diameter specifications, measurement method, panel dimensions, colour, edges, accessories and packaging. Record any agreed change before production.

Request a specification and sample review

Send your required mesh and panel sizes, application, quantity and destination, together with any existing sample reference or measurement photos. MaxCatNet can confirm the proposed construction, available combination and sample arrangements in the quotation.

Send a specification enquiry

Scroll to Top